View previous topic :: View next topic |
Author |
Message |
SpooNMan
Joined: 31 Oct 2007 Posts: 89
|
Posted: Wed Apr 30, 2008 9:35 pm Post subject: 2 broken SNES systems.. Anyone good with SNES hardware? |
|
|
I had 2 working SNES systems (sorta)
System 1 was fine and an original from release day (9/1991).
System 2 was given to me by a friend. It has weird issues. When putting in Super Mario World it would start you off invincible w/ music playing and everything. most gfx were garbled. Star Fox oddly enough works perfectly. SWC DX loads up but games won't load from the floppy. 4 other cartridges tested and all have screwed up gfx.
System 2 I tried cleaning the contacts of the carts and snes unit with alcohol. A Nintendo SNES cleaning kit and canned air were used for the system contacts.
Now here's where it gets worse! I opened System 1 in order to try the removable cartridge pin connector and as soon as I opened it the system refused to power on! I checked everything and even tried swapping the power on/off cable with System 2 and it still won't power on.
So now I am stuck with a dead original system (I grew up with this and had my SWC plugged into it for nearly 18 years so It had sentimental value) and a messed up System 2!
Anyone have any ideas (other than buying another or emulating it) I just want a working system. I would mainly like to get my original SNES ( System 2)working. Is there a fuse in the snes that can be removed? I have the system torn apart and I can't locate one.
Thanks guys. _________________ www.videogameobsession.com |
|
Back to top |
|
|
madman
Joined: 07 Jul 2006 Posts: 598
|
Posted: Thu May 01, 2008 4:39 am Post subject: |
|
|
Yep, there's a fuse in there, it's along the side, follow where the power goes in and you'll see. If a system doesn't turn on, this is most likely the reason why. Either replace the fuse, or just jumper the connection. |
|
Back to top |
|
|
SpooNMan
Joined: 31 Oct 2007 Posts: 89
|
Posted: Thu May 01, 2008 9:08 pm Post subject: |
|
|
madman wrote: | Yep, there's a fuse in there, it's along the side, follow where the power goes in and you'll see. If a system doesn't turn on, this is most likely the reason why. Either replace the fuse, or just jumper the connection. |
Is it the small soldered-in 1.5AMP piece? I guess they don't use standardized fuses at Nintendo... I gave the other gfx screwed system a 91% alcohol bath overnight and after letting it dry that doesn't boot either... I've never had so much trouble with consoles. _________________ www.videogameobsession.com |
|
Back to top |
|
|
madman
Joined: 07 Jul 2006 Posts: 598
|
Posted: Fri May 02, 2008 7:08 am Post subject: |
|
|
It's a regular picofuse, they didn't invent a new fuse just for the SNES. |
|
Back to top |
|
|
Data33
Joined: 01 Feb 2007 Posts: 18
|
Posted: Fri May 02, 2008 8:58 pm Post subject: |
|
|
SpooNMan wrote: | madman wrote: | Yep, there's a fuse in there, it's along the side, follow where the power goes in and you'll see. If a system doesn't turn on, this is most likely the reason why. Either replace the fuse, or just jumper the connection. |
Is it the small soldered-in 1.5AMP piece? I guess they don't use standardized fuses at Nintendo... I gave the other gfx screwed system a 91% alcohol bath overnight and after letting it dry that doesn't boot either... I've never had so much trouble with consoles. |
Not sure if this is needed info, but the fuse doesn't have to be a 1.5AMP one. I've fixed a couple of SNES'es with an 1.6AMP, which is easier to find. Also, jumpering this instead of putting a fuse there is dangerous. If something happens, your SNES will take the hit instead of the fuse.
//Data33 |
|
Back to top |
|
|
MrCheese
Joined: 07 Sep 2007 Posts: 103
|
Posted: Sun May 04, 2008 12:09 pm Post subject: |
|
|
Before opening a SNES you should unplug the power lead then switch it on. You will see the power LED flash briefly. Doing this drains the power inside the console. You have much less chance of blowing the fuse. |
|
Back to top |
|
|
Data33
Joined: 01 Feb 2007 Posts: 18
|
Posted: Sun May 04, 2008 8:09 pm Post subject: |
|
|
MrCheese wrote: | Before opening a SNES you should unplug the power lead then switch it on. You will see the power LED flash briefly. Doing this drains the power inside the console. You have much less chance of blowing the fuse. |
Hmm, I always thought there was no chance at all to blow the fuse if there's no current in the circuits? |
|
Back to top |
|
|
MrCheese
Joined: 07 Sep 2007 Posts: 103
|
Posted: Mon May 05, 2008 7:00 am Post subject: |
|
|
Capacitors. |
|
Back to top |
|
|
SpooNMan
Joined: 31 Oct 2007 Posts: 89
|
Posted: Wed May 21, 2008 10:40 pm Post subject: |
|
|
MrCheese wrote: | Capacitors. |
Why would you think it's a cap? I forgot to discharge the system prior to touching the board. I assume it's the problem.
I took some pictures of the board here
http://spoonman.roarvgm.com/videogame/snes_hardware/snes_hardware.html
**This is also the board that also had glitchy gfx in many games (back when it started up)
I tried everything I could think of and gave it the last ditch effort of an alcohol (91%) bath which has fixed some of my hardware in the past. No luck here though.
I'm going to buy some PICO fuses and see if that starts them up. I only need 2, but I can only find 5pks and higher. _________________ www.videogameobsession.com |
|
Back to top |
|
|
madman
Joined: 07 Jul 2006 Posts: 598
|
Posted: Thu May 22, 2008 12:27 am Post subject: |
|
|
Caps won't hold enough charge to blow the fuse. Maybe it'd blow if you had a cartridge inserted backwards (bare PCBs in with no case) and immediately turned it on right after removing the power supply, but very unlikely.
Spoonman, if you want you can just jumper the fuses to see if those are the issue. If jumpering doesn't power it up, it's not the fuse that's the issue. |
|
Back to top |
|
|
SpooNMan
Joined: 31 Oct 2007 Posts: 89
|
Posted: Thu May 22, 2008 7:23 pm Post subject: |
|
|
madman wrote: | Caps won't hold enough charge to blow the fuse. Maybe it'd blow if you had a cartridge inserted backwards (bare PCBs in with no case) and immediately turned it on right after removing the power supply, but very unlikely.
Spoonman, if you want you can just jumper the fuses to see if those are the issue. If jumpering doesn't power it up, it's not the fuse that's the issue. |
ok, I'll try that. Would any copper wire work to connect the points? _________________ www.videogameobsession.com |
|
Back to top |
|
|
madman
Joined: 07 Jul 2006 Posts: 598
|
Posted: Fri May 23, 2008 6:20 pm Post subject: |
|
|
Pretty much, yea. |
|
Back to top |
|
|
MrCheese
Joined: 07 Sep 2007 Posts: 103
|
|
Back to top |
|
|
|